How to Connect a Zoom H4n to a Mixer

Connect-H4n-to-Mixer
[su_heading style=”flat-dark” size=”30″ margin=”0″]TESTIMONIALS USING THIS METHOD[/su_heading]

thank you so so so so so much for taking the time to make this video. I am a wedding videographer and just bought the zoom H4N and was so frustrated with constant distortion when plugged into the dJ Board for a line out of board in into the H4N. I bought the attenuator and used your set up and it worked like a charm.

gigifaraci

Thank you RAVKAN. This was very helpful and well produced. I subscribed! Looking forward to your other video creations.

John Davis

By far the best tutorial I’ve seen on this. Thanks for showing the whole set up including the mixing board half. Most videos have been just showing how to use the H4N.

Taylor Kerby

 

[su_heading style=”flat-dark” size=”30″ margin=”0″]What is Audio Clipping / Distorting?[/su_heading]

When audio coming in reaches its maximum level / amplitude (or close to) on sound meters or a Zoom H4n, as seen in the image below, then you’ve run out of headroom which will in most cases result in Audio Clipping. In other words, the audio is being crushed and will sound distorted. The signal coming is is too hot for the mixer or device to handle. Essentially the signal “cuts” or “clips” when the audio signal hits it’s maximum capacity. See Waveform images below.

[su_heading style=”flat-dark” size=”30″ margin=”0″]What causes Audio Clipping / Distorting?[/su_heading] 

In short, an overloaded signal being sent from the amplifier to the audio mixer or recording device.

The Waveform images below show when and how the audio is too high and too low, both situations you don’t want to be in!

Zoom-h4n-levels-too-high-clipping

Zoom-h4n-levels-too-low

[su_heading style=”flat-dark” size=”30″ margin=”0″]HOW TO FIX THIS[/su_heading]

[su_highlight background=”#a5190b” color=”#ffffff”]ANSWER[/su_highlight] With an Attenuator

Audio Attenuators essentially lower the volume / amplitude of audio and are defined in a number in decibels, This reduction in the wave amplitude really helps if you’ve connected a Line Level output to a Mic input as shown in this article.

By the way, Clipped Audio cannot be fixed completely in post. Small issues can be ‘fixed’ but even this is hit and miss. This best way I’ve found, along with many others I’ve shown this method to, is to prepare the audio setup before recording anything. It’s a really easy method and you can read the steps below on this.

Below you will see what the waveform amplitude looks like when an Attenuator is connected to an XLR cable.

connect-zoom-h4n-to-mixer-good-level

[su_box title=”IMPORTANT” box_color=”#9e0202″ radius=”0″]The Zoom H4n only takes Mic Level inputs at the bottom and cannot take Line sources.[/su_box]

This is crucial as a Line Level cable uses greater voltage than a mic-level signal, around 1,000 times greater compared to a Microphone Level input which uses 0.010 volts. See images below. Please watch the video where Curtis Judd explains how to
Record Live Event Sound from a Mixing Board

line-and-mic-level

So, getting a Line Level TRS (or RCAs) to XLR cables and just plugging them into the Zoom H4n will give you clipping / overload issues. You need to attach things in front of the XLRs to avoid this. Those things are Attenuators as shown below.

Audio-Attenuators

You can use any of the two types of connectors (TRS or RCA) incase one is used up on the mixer. Then plug those into the Attenuators and the Zoom H4n.
Also, I have never experienced any difference in signal / sound quality when using either connectors.

 

[su_heading style=”flat-dark” size=”24″ margin=”0″]STEPS FOR CONNECTING THE ZOOM H4N TO A MIXER[/su_heading]
connect-h4n-to-mixer-trs-cable

Cable 1: TRS to XLR cable

This Line Level 1/4″ TRS cable is needed to use the Aux Sends on the audio mixer

connect-h4n-to-mixer-rca-cable

Cable 2: RCA to XLR cable

This Line Level RCA cable is needed to use the Tape Outs on the audio mixer

-20 DB  Attenuators

These are needed to LOWER the volume / amplitude of audio and are defined in decibels

connect-h4n-to-mixer-trs-cable-attenuator-connect

Fix Attenuators on TRS or RCA cable

This setup will now reduce the volume / amplitude of the audio recorded into the Zoom H4n

To read about how to Connect a Zoom H1 to a Mixer click here OR click on the image below

Connect-zoom-h1-to-mixer-link

Cable 1: Insert the TRS cables into the Aux Sends of the Mixer

The audio level can be adjusted using the Master level of the Aux Send

connect-h4n-to-mixer-rca-cable-tape-out

Cable 2: Insert the RCA cables into the Tape Output of the Mixer

As the Tape Out is a fixed output, the incoming audio level is adjusted on the Zoom H4n inputs

connect-h4n-to-mixer-adjust-aux-master

Adjust the Aux Master 

This is the Master volume control for the Aux Send

connect-h4n-to-mixer-trs-cable-zoom-h4n-inputs

Insert the Cables with Attenuators into the Zoom H4n Inputs

Make sure cable Left and cable Right are in the correct inputs

connect-h4n-to-mixer-play-audio

Play Audio to record

Whether it’s a vinyl or CD

connect-h4n-to-mixer-adjust-record-levels

Check the Input levels on the Zoom H4n

Keep it as close to -6db so there is plenty of headroom

[su_heading style=”flat-dark” size=”30″ margin=”0″]WATCH VIDEO BELOW[/su_heading]

[su_heading style=”flat-dark” size=”30″ margin=”0″] EQUIPMENT NEEDED[/su_heading]

[su_highlight background=”#a5190b” color=”#ffffff”]NOTE[/su_highlight]

Please make sure you buy 2 X TRS to XLR cables and 2 X Whirlwind IMP Pad -20 DB (Attenuator).

[su_heading style=”flat-dark” size=”30″ margin=”0″] EQUIPMENT NEEDED[/su_heading]

[su_highlight background=”#a5190b” color=”#ffffff”]NOTE[/su_highlight]

Please make sure you buy 2 X RCA to XLR cables and 2 X Loops -20 DB (Attenuator). Some items are listed incorrectly.

Zoom H4n Pro

Jack to XLR Leads

RCA to XLR CableS

Loops -20dbAttenuator

Leave a Reply

Your email address will not be published. Required fields are marked *